NOTE: For best results, read each step carefully and entirely before proceeding to the next.
Filling Your Spa
Wipe the interior of the spa with a damp, soft cloth to remove any residue that may be on the surface. Fill with a garden hose by inserting the nozzle of the hose in the filter inlet. (After filling is complete, remember to put the filter cartridge in place prior to starting the spa.) As the spa is filling, check in the equipment access area for any leaks. On occasion, it may be necessary to hand tighten a union fitting that may have come loose during transit. Also check that the gate valves are pulled out to the open position and that the hose bib is closed. Continue to fill to the water line.
NOTE: If your water is extremely hard, it is preferable to fill the spa halfway with hard water and the rest with softened water. Never fill the spa entirely with softened water.
Initial Start Up
Your spa has been programmed for your convenience. Once properly connected, the H.E.E.T. circulation pump, heater and BiOzone water purification system will automatically come on, heat the spa to 102 F and introduce ozone 24 hours a day. Initial temperature, day, and time can be set and changed by following these instructions.
A. Setting Permanent Temperature:
1. Press “PROG” to enter the programming mode. Notice the heater icon flashing.
2. Press “UP” or “DOWN” arrows to choose the desired temperature. NOTE: There is a procedure to choose a different temperature for each day of the week (See “Advanced Features–Heat Days”).
B. Setting Current Day:
1. Press “VIEW” to show the day of week. Notice the clock icon flashing.
2. Press “UP” or “DOWN” to select the current day. Choose 1 for Sunday, 2 for Monday, so on and so forth up to 7 for Saturday.
NOTE: To change current day directly, do step A1 & B1.
C. Setting Current Time
Press “VIEW” to show the Hour. Observe the PM indicator. No indicator means AM. Press “UP” or “DOWN” to select the current hour. Press “VIEW” to show the minutes. Press “UP” or “DOWN” to select the current minute. NOTE: To change current time at any time, press the “PROG” button and then press the “VIEW” button twice to display time.
Returning To Regular Display:
Wait 30 seconds or press any button to exit the programming mode.
|
A. Displaying Time or Temperature
Pressing the “VIEW” button will switch the display between current time and current water temperature.
B. Temporarily Adjusting Temperature
If you like to temporarily change your water temperature setting, up or down, during any one day, you can do so for the current day by switching to the current temperature display (press “VIEW”) and by pressing the “UP” or “DOWN” arrows. The “adjusted” temperature will be in effect until midnight that day, at which point, the temperature setting will revert back to the original setting for that day. Notice the flashing heater icon while making this change.
C. Water Jet Therapy
Your spa is equipped with one or two
2-mode therapy pumps. The soft-mode (Low) provides soft Relaxation Therapy and the power-mode (High) provides vigorous Power Therapy.
Dual Pump Systems:
Press “JET” to activate the Relaxation Therapy mode. Both pumps will turn on to service every seat.
Press “JET” to activate the Power Therapy mode. Pump #1 will turn on.
Press “JET” to activate pump #2 in Power Therapy mode. Both pumps will be on.
Press “JET” to de-activate pump #1.
Pump #2 will remain in Power Therapy mode.
Press “JET” to de-activate pump #2. Both pumps will be off.
Note that for safety, all jet modes will automatically turn off after 30 minutes. Re-activate any therapy mode as indicated above.
D. Air Injection/Aroma Button
Your spa is equipped with an air therapy pump. A touch of the pump button activates the power-mode for air bubble action and induction of air into the Chromatherapy (aromatherapy) system. Touching the blower button again will turn it off. For safety, the pump will automatically turn off after 30 minutes.
To reactivate, start sequence over.
E. Turning On The Light
Your spa has an underwater light. A single touch of the Light button turns the light on. A second touch turns the light off. If left on, the light will automatically turn off after three (3) hours of continuous operation.
F. Inverting Display
The Selectron Plus display can be inverted to allow easier reading from inside the spa. To do so, first make sure “TIME” is displayed. Use “VIEW” button to change to “TIME” display if needed. Then press the “DOWN” arrow for approximately 10 seconds to invert the display. Follow the same procedure to revert the view back to its original position.
|
Go Back 
