A. Surround Stereo System (Optional)

Country Code Setting
Advance the programming sequence to the minute set position.

Hold down the “PROG” for 5 seconds and observe that the screen shows CO=X (where X is either U for USA, E for Europe, or J for Japan)

Use the “UP” or “DOWN” buttons to change the country, as required

Stereo Access and Volume Control

To access the stereo, press “UP” and “DOWN” buttons on the spa control pad simultaneously. The stereo will turn on, and you will automatically be taken to the volume control.

Your volume range is L0 through L8(L=00 equal off and L=08 is the loudest).

Bass

While in the volume mode, press “PROG”

Bass range is B00 through B008

Frequency Source

From Bass Mode, press “PROG” to select source.

After source is selected, press “PROG” to exit selection or use “UP” or “DOWN” keys to scan stations.

In S=L you can connect optional Vita CD player, or any other personal stereo device, such as a walkman or MP3.

The “VIEW” button can be pressed to escape the stereo mode.

B. Fresh Water Misters

Connection

Connect garden hose or supplied adapter and Poly Hose kit from fresh water source to spa “Inlet”

Activation

Turn on water source.

To activate misters, open valve located within spa filtration compartment. Spa does not need to be operating to operate misters.

Maintenance

Periodically Flush or replace in line filter. Located inside panel (same side as water source inlet). See your dealer for availability or replacement

If Mister heads become clogged unscrew (counterclockwise) and clean using a small probe such as a needle

C. Remote Control

Your spa model may come equipped with a remote control located on the opposite side of the spa from the main spa side control. When pressing "SOAK" this will operate jets one and two in low speed. Pressing "JET 1" , "JET2, or "JET 3" is high speed only. The "LIGHT" button will activate your light. The “aux” button will operate blower. It can not be used to program the spa.

Note: your Optional “Floating Remote” instruction book is located in a seperate manual.

D. Chromatherapy

The Chromatherapy option is activated by pressing the Light button on the spa side control.
To program the lights, press and hold the Light button for 5 seconds.

Once the display reads L=XX, release the button.
Using the arrow buttons, you may select the different settings.

Review each setting to determine which is best suited for you. The selection may be changed at any time by repeating the previous steps.

L=00 Off
L=01 Diamond
L=02 Blue
L=03 Green
L=04 Red
L=05 Strobe effect Red/Green/Blue
L=06 Gradual change Red/Green/Blue
L=07 - 10 Combination Colors
L=11 - 20 Reduce Intensity 50%
L=21 - 20 Reduce Intensity 75%

The lighting system will automatically turn itself off after three (3) hours.

E. Waveseat

Activation

The waveseat can be activated from either the topside control or the remote control. From the Topside control, one must press the “LIGHT” button twice to activate the waveseat pump. From the Remote control one presses "JET 3". The lights will remain on while the pump is in operation.

Speed Switch

The speed switch may be used to select time between cycles. The speed switch will only function when the user has selected one of the six sequences. Default speed is the slowest, there is a 15 second delay between each step (light will blink slowly). Depressing the speed key once will delay 10 seconds. Twice will reduce another 5 seconds between cycles (light will blink rapidly). Three times, it will return the cycle delay time to 15 seconds.

Pause Switch

To interrupt your massage sequence. You can stop the cycles and keep the jets working in that particular spot for as long as you like or until the main control times out after 30 minutes. To restart wave action, press the Pause switch a second time. If the Pause switch is activated, the first indicator light will stay on.

Sequence Switch

Allow the user to select the type of massage they want. A total of 6 different sequeces are programmed into the system including one, in which, all the valves are open. The lights on the control pad indicated which cycle is operating at the time. If all valves are open, the light indicators should be off.

The press of the switch will sequence the cycles forward. they can not be reveresed or modified. The L.E.D. will flash for the corresponding cycle. There are four lights that illustrate the jet pattern. the user can preview the cycle selected at an accelerated rate for 5 seconds prior to its actual start. To accept the selected cycle, do not touch the keypad for 5 seconds. The system will then acknowledge the selected cycle and display the L.E.D.