A. Circulation Pump (Optional)

Setting Circulation pump

You are given the choice between 12 forced hours of circulation or 24 forced hours, regardless of water tempature.

1. Press “PROG” and hold until “AH” flashes
2. Press “PROG” 4 times “C=12” appears.
3. Press “UP” or “DOWN” buttons to change.
4. Press “LIGHT” button to clear or wait 30 seconds.

B. Skim-Away (Only Available with Optional Circulation Pump)

Skim–Away is an automatic skimming action which takes place each day from 8am until 8:30am each morning and from 4pm until 4:30pm each afternoon. The primary and secondary pumps will activate in low speed mode. This will pull all surface oils and debris into the filter well cavity. This setting permits the skim-away feature to operate for 30 minutes each morning and afternoon for a total of 1 hour each day.

1.Press and hold “PROG” until “AH” flashes
2.Press “PROG” three times to show “SA=1” which is the factory setting.
3. Pressing the “UP” or “DOWN” arrows, you can change the skim-away tim to 2, 4, or 6 hours each day.

The total selected time will be split between morning and afternoon.

Econo Package / LC Upgrade:

Your spa has been full foamed at the time it was manufactured and is equipped with a circulation pump. After the first twelve hours of operation each day, as a protection against overheating, the pump will turn off if the water temperature exceeds the desired temperature. The pump will comeback on when the water temperature falls 1 degree Fahrenheit under the desired temperature. This will then activate the heater.

C. Air Injection Thererapy Air Button

This option equips your spa with an air therapy blower. Press the “AUX” to activate and de-activate the air therapy blower. For safety, the blower will automatically turns itself off after 30 minutes.

Automatic Blower and Jet Purge
Once each day, at 10 AM the jet pump(s) will automatically run for one minute to circulate potential stale water in the piping. This is a
normal function of the spa. The display will show “BJ2P” while this takes place.

D. Fresh Water Misters

Connection
Connect garden hose or supplied adapter and Poly Hose kit from fresh water source to spa “Inlet”

Activation
Turn on water source.
To activate misters, open valve located within spa filtration compartment or top of spa depending on model. Spa does not need to be operating to operate misters.

If Mister heads become clogged unscrew (counterclockwise) and clean using a small probe such as a needle

E. Surround Stereo

Country Code Setting
Advance the programming sequence to the minute set position.

Hold down the “PROG” for 5 seconds and observe that the screen shows CO=X (where X is either U for USA, E for Europe, or J for Japan)

Use the “UP” or “DOWN” buttons to change the country, as required.

Stereo Access and Volume Control
To access the stereo, press “UP” and “DOWN” buttons on the spa control pad simultaneously. The stereo will turn on, and you will automatically be taken to the volume control.

Your volume range is L0 through L8(L=00 equal off and L=08 is the loudest).

To adjust the volume level press “UP” or “DOWN” arrows.

Bass
While in the volume mode, press “PROG”.

Bass range is B00 through B008

Frequency Source
From Bass Mode, press “PROG” to select source.

S=A equals A.M., S=F equals F.M., S=L equals line input.

After source is selected, press “PROG” to exit selection or use “UP” or “DOWN” keys to scan stations.

In S=L you can connect optional CD player, or any other personal stereo device, such as a walkman or MP3.

F. Chromatherapy (Optional)

The Chromatherapy option is activated by pressing the Light button on the spa side control.
To program the lights, press and hold the Light button for 5 seconds.

Once the display reads L=XX, release the button.
Using the arrow buttons, you may select the different settings.

L=00 Off
L=01 Diamond
L=02 Blue
L=03 Green
L=04 Red
L=05 Strobe effect Red/Green/Blue
L=06 Gradual change Red/Green/Blue
L=07 - 10 Combination Colors
L=11 - 20 Reduce Intensity 50%
L=21 - 20 Reduce Intensity 75%